Forge Eliminator DV
This is a discussion on Forge Eliminator DV within the Forge Motorsport forums, part of the BRISKODA Partners category; I've been testing a new valve from Forge, called the Eliminator. Its basically an uprated diaphragm type recirculating DV that ...
| |||||||
Pronounced "bris-skoda", a brisk skoda. | Register | FAQ | Members List | Calendar | Mark Forums Read |
09-11-2005, 16:49
| #1 |
| Briskodian Join Date: Jul 2004 Location: Liverpool
Posts: 13
Thanks: 1
Thanked 0 Times in 0 Posts
|  Forge Eliminator DV I've been testing a new valve from Forge, called the Eliminator. Its basically an uprated diaphragm type recirculating DV that uses an stronger LT Polymer (or, polyaryletherketone polymer as its called in some circles) diaphragm, to hold boost. Heres a link to the review: http://www.uk-mkivs.net/blogs/uk-mki...09/388908.aspx Theres also a link at the start of the article to the prototype review I did. Release date is planned for December - just in time for Chrimbo folks! Should fit nicely into those stockings  |
|    |
|
09-11-2005, 18:25
| #2 |
| BRISKODA Staff  Join Date: Oct 2002 Location: darkest Hampshire
Posts: 8,650
Thanks: 0
Thanked 17 Times in 13 Posts
| Didn't GaryM have the Forge Optimus which was also a diaphragm type dv? Wonder if this is the same but renamed?
__________________ Adrian. |
|
| |
|
09-11-2005, 19:01
| #3 |
| Briskodian Join Date: Jul 2004 Location: Liverpool
Posts: 13
Thanks: 1
Thanked 0 Times in 0 Posts
| It's a new piece of kit with an uprated diaphragm. Similar in design to the Optimus in how it works though. I've been using this one for the last week now and its responding extremely well  |
|
| |
|
24-11-2005, 12:01
| #4 |
| Briskodian Join Date: Nov 2002
Posts: 557
Thanks: 0
Thanked 0 Times in 0 Posts
| Re: Forge Eliminator DV How much is it compared with the 007? |
|
| |
|
19-02-2006, 19:51
| #5 |
| Briskodian Join Date: Nov 2002 Location: North
Posts: 2,709
Thanks: 0
Thanked 0 Times in 0 Posts
| Re: Forge Eliminator DV Just to resurrect this thread... After taking advice elsewhere I'm getting one of these tomorrow. Hopefully it will do away with the problems I've been having with piston DVs.
__________________ Rich. Skoda Octavia RS |
|
| |
|
20-02-2006, 17:58
| #6 |
| Briskodian Join Date: Nov 2002 Location: North
Posts: 2,709
Thanks: 0
Thanked 0 Times in 0 Posts
| Re: Forge Eliminator DV OK so I’m now all Eliminator’d up! Awesome were nearest to me with stock so off I went. After fitting response does seem to be a bit quicker but I’m not sure if I’m imagining that. The main thing is that I don’t have to worry about aluminium filings anymore. If you didn’t already know, the Forge Eliminator comes with two additional springs and shims. Taking on board the advice of the chaps at Awesome and GaryM it does appear that the stock spring is more than suitable. I’ve got a run up to Edinburgh tomorrow so if my opinion on that changes I’ll let you know.
__________________ Rich. Skoda Octavia RS |
|
| |
 |
« A BIG thank you....
|
Thank You »
| Thread Tools | |
| Display Modes | |
Linear Mode
|
|
All times are GMT +1. The time now is 03:17.
